Custom Valve | Custom Regulator

You are here:

Home » Custom Valve Technology » Valves & Regulators

Valves & Regulators

Controlling the flow of gas is at the heart of every device we create. Our flow control technologies include: twist to control, push to control, trigger actuation, ball valves, burst valves, dump valves, check valves, needle valves and pressure relief or safety valves.
Whenever you need a solution, think of Genuine Innovations to help you choose the right valve for you.

CO2 / Gas Composite Regulator

Regulator

Part SA00196

This is an inexpensive Composite Gas / CO2 Regulator with the capability to control high-pressure gas cartridges or cylinders with an adjustable flow range of 15 to 150 PSI. Accepts 1-12 UNF threaded innovations cup. Adapters are available for most threaded cartridges as well. Patented.

More Information

Regulator Kit w-CO2

Regulator Kit

Part 32100

This kit provides all the items to experiment with an adjustable composite regulator and on/off valve. One 16 gram CO2 cartridge is included, as well as instructions.

More Information

Regulator Composite Kit

Regulator Kit

Part 32101

This is the same kit as the 32100, but does not include the CO2 cartridge.

More Information

Dual Stage Regulator Kit

Regulator Kit

Part 32110

This kit uses two of our composite regulators connected together for very low pressure outputs.

More Information

Airbrush Kit

Regulator Kit

Part 32200

This kit includes the adjustable output portable air brush, 16 gram CO2 gas cartridges and instructions.

More Information

Aluminum Regulator

Regulator

Part 5049

Genuine Innovations Patented Aluminum Gas Regulator can regulate high-pressure gas cartridges to an adjustable range of 15 to 150 PSI. The regulator is threaded at the bottom to accept 1-12 UNF Threaded Innovations cups as well as 3/8-24 threaded cartridges. Patented.

More Information

Ultraflate Plus Kit

Regulator Kit

Part 32300

This kit includes one of our most popular inflators; the Ultraflate Plus. Included in the kit are CO2 cartridges and instructions for use.

More Information

Portable Air Brush

Regulator

Part SA00109

The Portable Airbrush uses Genuine Innovations patented composite Gas Regulator and LPV to control the gas flow from 16g CO2 cartridges. The gas is precisely controlled to flow over the paint nozzle to spray various liquids including paint and other liquid solutions.

More Information

Ultraflate Plus Bulk

Trigger Control

Part 2423

The Ultraflate Plus valve system features front position trigger valve and brass outlet for Schrader and Presta Tire valves. A safety lock prevents accidental discharges. The valve system uses our Patented 12g or 16g Cylinder MultiCup Cartridge Holder.

More Information

Ultraflate

Trigger Control

Part 2413

The Ultraflate inflator pump features a trigger actuated valve, brass outlet for Schrader and Presta Tire Valves and a 12g Cup Cartridge Holder. See Available Options for variations to this versatile pump.

More Information

Ultraflate 2 Bulk

Trigger Control

Part 2411-B

A versatile inflator with an integral locking mechanism and push-to-inflate technology. Features a threaded outlet and fits Schrader and Presta Tire Valves. Accepts 12/16g smooth neck cartridges. Permits use of 3/8-24 standard threaded cartridges without the cup.

More Information

QS16 Pro Bulk

Trigger Control

Part 4434-B

The Helmet Head uses a ball/valve technology and locking mechanism to help prevent accidental discharge. The lock is a push-on/push-off positive locking mechanism. The pump features a thumb trigger actuated valve, an outlet that fits both Schrader and Presta Tire Valves, and a 16g Cup Cartridge Holder.

More Information

Microflate Nano

Twist Control

Part 2331

The Microflate Nano uses Genuine Innovations Twist-to-Control technology with a 3/8-24 thread to use 12, 16, 25 gram cartridges and Big Air!. Gas is released in a controlled fashion by turning the cartridge to adjust flow or shut off the valve.

More Information

Microflate

Twist Control

Part 2351

The Microflate uses twist-to-control technology: Thread a 3/8-24 cartridge into the Microflate, and then tighten until the cartridge is pierced. To release the gas, unthread the cartridge approximately ½ to 1 turn. Gas is released in controlled fashion by threading and unthreading the cartridge to adjust flow or shut off the valve.

More Information

Air Chuck SL

Push Control

Part 2364

An easy-to-use, lightweight inflator from Genuine Innovations

More Information

Monster Air Chuck

Push Control

Part 3361

The Monster Air Chuck uses push-to-inflate control. It accepts 5/8-18 cartridges. On top is a depression to allow adding your custom designed round label. Other finishes also available.

More Information

Big Shot Bulk

Twist Control

Part 4525

The Big Shot Microflate uses twist-to-control technology: Drop a 16g Non Threaded cartridge into the Big Shot MF Cup and then tighten until the cartridge is pierced. To release the gas, unthread the cup approximately ½ to 1 turn. Gas is released in controlled fashion. The nozzle can be fitted onto Schrader or Presta valves. Available Options include custom colors.

More Information

Ultraflate Blower w/Straw

Blowers

Part SA00122

The Ultraflate Blower uses the Ultraflate head and a special brass outlet with a plastic blower straw using .007” restriction to reduce and direct the flow of gas into small areas. The stock blower is available with the gray Patented Multicup for use with 12g and 16g...

More Information

Low Pressure Valve

Valve

Part SA00195

The Low Pressure Valve (LPV) (SA00195) is constructed of High-strength glass-reinforced nylon. It is used as a control valve and is available as an on/off or three-way controller. The LPV features one input and two output ports and includes a molded mounting hole and posts, providing for several mounting options. The LPV can be used in your custom projects or in conjunction with our composite high-pressure regulator. (SA00196)

More Information

Composite Relief Valve

Valve

Part 4102

The Composite Pressure Relief Valve (PRV) is constructed of High-strength glass-reinforced nylon. It can be used as a pressure relief valve for Genuine Innovations Valve Systems. A restrictor slows the high pressure gas flow into PRV to allow the relief system to accurately control the output gas pressure. The PRV utilizes GI’s standard tail geometry and can be used with the stock Ultraflate, Ultraflate Plus, and Microflate. PATENTED

More Information

Pressure Relief Valve - Brass

Valve

Part 4110

Brass Pressure Relieve Valve

More Information

Valve Assembly UF

Valve

Part SA00101

The brass UF Valve Assembly is the heart of our Ultraflate product line of inflators and blowers and can be custom fit for unique applications. The valve assembly uses our lance to pierce the gas cartridges.

More Information

Valve Assembly - MF

Valve

Part SA00068

Valve assemblies are the internal valve subassembly from our Stock Valves and can be used to pierce the cap of threaded cartridges and control the gas flow.

More Information

In-Line Microflate

Valve

Part MM235008-11N

The all brass body In-line Microflate uses Genuine Innovations Twist-to-Control technology: Thread a 3/8-24 cartridge into the Microflate, and then tighten until the cartridge is pierced. To release the gas, unthread the cartridge approximately ½ to 1 turn. Gas is released in controlled fashion by threading and unthreading the cartridge to adjust flow or shut off the valve.

More Information

In-Line MF (Long Version)

Valve

Part MM235008-21N

The all brass body In-line Microflate uses Genuine Innovations Twist-to-Control technology: Thread a 3/8-24 cartridge into the Microflate, and then tighten until the cartridge is pierced. To release the gas, unthread the cartridge approximately ½ to 1 turn. Gas is released in controlled fashion by threading and unthreading the cartridge to adjust flow or shut off the valve.

More Information

Lance Assembly UF

Lance

Part SA00102

Valve assemblies are the internal valve subassembly from our Stock Valves and can be used to pierce the cap of threaded cartridges. The Lance Assembly UF is machined from ½” hex stock. It has 3/8-24 threads to accept gas from high pressure cylinders into the system to allow the gas to pass through into a separate valve control system.

More Information

Custom Outlets

Outlet

Part SA00153

GI Outlets or Nozzles are the output subassembly that attach to Genuine Innovations Stock Valves. They use our standardized tail stock geometry and can be integrated with most of our stock valves. The GI Outlets are machined from brass stock.

More Information

Blower Straw

Outlet

Part SA00106

The Blower Straw uses Genuine Innovations standard tail stock geometry with .007” restrictor orifice. The polypropylene straw further restricts the gas flow into a precise flow pattern that is great for dust blowing applications.

More Information

Brass Adapter 1-12

Adapter

Part 32010

The Adapter 1-12 converts Genuine Innovations 1-12 UNF products like the Ultraflate and Regulators to adapt to 3/8-24, 1/2-20, 5/8-18, 16x1.5mm threaded cartridges and CGA-320 for refillable tanks.

More Information

Loading...